Pool water cloudiness always makes one blame the filter. While it could be the culprit, it might be due to poor water chemistry, high swimmer traffic or low hours of operation of the pump. It is important that those intending to install pool media filters in Perth know what filtration involves as well as what other aspects of pool maintenance are involved.

Pool Water Clarification Through Filtration and Sanitation
While the filter removes suspended matter such as leaves, hair and particles from the water, the sanitiser kills bacteria. This is why there is mention of water filtration as well as sanitisation in the WA health advisory on pool maintenance. In the case of an outdoor pool, the minimum free chlorine requirement is 2 mg/L of water at temperatures below 26°C, while at higher temperatures the minimum required is 3 mg/L.
This is especially important when choosing pool media filters Perth since Perth has very hot summers. Chlorine operates effectively at pH ranging from 7.2 to 7.8, with 7.5 being optimum for swimmers.
Sand, Glass and Cartridge Filters: How They Really Work?
Sand and glass filters are called media filters because the water goes through a layer of tiny particles. Each kind has its own way of getting cleaned:
- Sand filters: Usually get a good clean by reversing the water flow through backwashing, basically the opposite of what it normally does.
- Glass media filters: Same deal as sand filters, just basically take the water the wrong way to clean them out.
- Cartridge filters: Need to be taken out and cleaned by hand, pretty straightforward.
Now, whatever you do, you should check the manufacturer’s instructions; different models have different needs. And, it really comes down to what kind of maintenance you can stick to; a well-cleaned filter will generally perform better than one that gets left to clog up.
How Long Will Pool Water Just Keep Circulating?
The Western Australian health guidelines reckon you should aim to get all the water in the pool going through the filter every 6-8 hours. This is actually how long it takes to turn the whole lot over, not some set amount of hours each day the pump’s on for. The time it needs to run will depend on the pump itself, the plumbing and the size of the filter you’re using.
Ideally, the filter should keep going as long as there are swimmers in the pool and for at least an hour after the last one’s gone. Spas are a bit different; the water’s got to keep turning over every 15 minutes, and you should also make sure it’s running a bit before and after use.
When Filter Pressure Rises and Checking Water Chemistry?
When the pressure gauge goes up, it usually means the filter needs cleaning. If you haven’t got a pressure gauge to help you out, you might need to rely on the obvious signs like when the water stops flowing back into the pool as quickly as it used to. Water testing is just as important, with the free chlorine and pH levels checked at least once a day.
In really hot weather you’re going to need to keep a closer eye on things; it’s a good idea to test before the first swim and again later in the day to see if there’s been any change.
What to Do When Pool Water Turns Green or Goes Milky?
Algae can turn your pool water green in what feels like no time in the middle of a Perth heatwave. The health guidelines say that rather than trying to clean the algae out of the filter while it’s still floating around, just get the brush to it, let the algae settle and then clean it out the next day.
Milky water’s a different story altogether; it happens when salt-chlorinated pools are used too much. You’ll know it’s happened because the water will go milky and the pool will need to be closed until it clears up. It just goes to show how important water testing and regular maintenance are.

Pool Covers and Looking After Your Pool in the Cooler Months
If you’re not using your pool for a bit during the winter, a decent pool cover will help protect it. The guidelines say to run the pool or just the motors for an hour each week and throw in a bit of chlorine to keep the bacteria at bay. And don’t forget to give it a good vacuum before next summer’s swimming season.
Pool covers are great at saving water but they can actually heat up the water surface during the summer and make algae growth more likely. So maybe think about when you’re using it, season by season; a cover that’s great in July might cause you problems in January.
Leave a comment